Posts made by Jay Bee

• Final Solution Heat Management

  @Chip Spencer No, I don't. No need for it. But you could. I think it probably will throttle after 10mins of full load.

  posted in General Discussion

  JB

  Jay Bee
  10/29/21, 11:05 PM
• Our Raspad Online Tutorial is launched today!

  The links seem to be dead. Cannot access the web pages from Europe.

  posted in General Discussion

  JB

  Jay Bee
  10/13/21, 12:50 AM
• Final Solution Heat Management

  For those who want to keep the accelshim, this might be helpful:   40 Pin GPIO Stacking Header  

  posted in General Discussion

  JB

  Jay Bee
  9/2/21, 6:05 AM
• Raspad team is soliciting Slogan from everyone!

  Thank you very much for the keybord gift. Has arrived safely at my home promptly after you annoucement. :-)

  posted in Deals & Giveaways

  JB

  Jay Bee
  8/30/21, 3:58 AM
• Final Solution Heat Management

  Agreed.   (1) I had removed the accelshim as it was of no use for me. So, I am not missing the auto-rotation. If it would really be need, then a short extension cord would help as the GPIO p...

  posted in General Discussion

  JB

  Jay Bee
  8/30/21, 3:47 AM
• Final Solution Heat Management

  Source: Click

  posted in General Discussion

  JB

  Jay Bee
  8/29/21, 12:36 AM
• Final Solution Heat Management

  posted in General Discussion

  JB

  Jay Bee
  8/29/21, 12:35 AM
• Final Solution Heat Management

  posted in General Discussion

  JB

  Jay Bee
  8/29/21, 12:34 AM
• Final Solution Heat Management

  posted in General Discussion

  JB

  Jay Bee
  8/29/21, 12:34 AM
• Tipps and Tricks

  #8: Final Solution on Heat Management: See here: https://raspad.com/community/forum/topic/35813/finale-solution-heat-management

  posted in General Discussion

  JB

  Jay Bee
  8/29/21, 12:32 AM
• Final Solution Heat Management

  Armor Case (Berrybase). Around 35°C at idle Below 60°C at high loads

  posted in General Discussion

  JB

  Jay Bee
  8/29/21, 12:30 AM
• Tipps and Tricks

  #7   The Raspad doesn't turn off the display when shutdown via Menu/Shell. Pi turns off, but not the rest. So do not forget to also hit the on/off button after Pi shut down, as it would alwa...

  posted in General Discussion

  JB

  Jay Bee
  6/2/21, 10:46 PM
• Raspad team is soliciting Slogan from everyone!

  Raspad - The Pi Maker's mobile Tool #1. Raspad - Pi up your Maker's Life. 

  posted in Deals & Giveaways

  JB

  Jay Bee
  6/2/21, 10:37 PM
• Tipps and Tricks

  @RasPad Support Many thanks for the hint. I will test and report.

  posted in General Discussion

  JB

  Jay Bee
  5/24/21, 6:10 PM
• Tipps and Tricks

  @Méziane Bourassé Yes, simply remove the internal SD Card adapter and plugin an SD card. Works just fine.

  posted in General Discussion

  JB

  Jay Bee
  5/21/21, 2:49 AM
• Tipps and Tricks

  #6   There is a little switch next to the fan connector on the Raspad daughter board which sets the cpu fan speed from Hi to Lo. This reduces the noise somewhat.   Jay

  posted in General Discussion

  JB

  Jay Bee
  5/19/21, 5:04 AM
• noisy fan

  @David Hardingham It will climp over 70 degree C very fast and if you have load it'll go over 80 and then trottle the clock rate. 

  posted in General Discussion

  JB

  Jay Bee
  5/19/21, 5:01 AM
• Raspad 3.0 : First impressions.

  That is too bad! Hope you will get your replacement soon.   Jay

  posted in General Discussion

  JB

  Jay Bee
  5/19/21, 12:29 AM
• Tipps and Tricks

  #5   The autorotate feature was too sensitive and I often had to rotate the Raspad to keep it in the desired mode (landscape mostly). I have removed the sensor from the Pi4 GPIO pins for now...

  posted in General Discussion

  JB

  Jay Bee
  5/19/21, 12:28 AM
• noisy fan

  I just tried another solution: I removed the fan and the small black heat sink from the SoC. I replaced it with two Pi4 SoC heat sinks by glueing the thermal pad half/half onto the surface. Meanin...

  posted in General Discussion

  JB

  Jay Bee
  5/19/21, 12:08 AM
• Tipps and Tricks

  #4 If you intend to program your Sunfounder STEM device using Raspad, the EZBlock 2 app needs an update to work with the BT dongle provided by Sunfounder customer support. However, there is a publ...

  posted in General Discussion

  JB

  Jay Bee
  5/18/21, 9:43 PM
• Tipps and Tricks

  #3 I noticed the external HDMI port is not hot plugable. Simply reboot the Raspad with the monitor plugged in and it will be activated.   Jay

  posted in General Discussion

  JB

  Jay Bee
  5/18/21, 8:50 PM
• Tipps and Tricks

  #2 I noticed static noises on the headphone jack. I am using BT paired device instead now. You need to install  sudo apt install bluetooth pi-bluetooth bluez blueman Then add Volume Control...

  posted in General Discussion

  JB

  Jay Bee
  5/18/21, 8:48 PM
• Tipps and Tricks

  Hi all,   #1 quick tipp to avoid destroying your SD card reader: never forget to remove SD card prior to opening the housing! The metal case of the reader will not survive an opening with a...

  posted in General Discussion

  JB

  Jay Bee
  5/18/21, 8:41 PM
• noisy fan

  I have fiddled around with the voltage level of the fan, but even if it runs very slowly, it is noisy. I believe we need to look into a big heat sink solution (similar to PI400) as the housing of t...

  posted in General Discussion

  JB

  Jay Bee
  5/18/21, 8:39 PM
• Register Our RasPad Community Account and Win Awesome Prizes!

  Thanks! :-)

  posted in Deals & Giveaways

  JB

  Jay Bee
  5/18/21, 8:35 PM